Blog

What Is Dead Reckoning and How Simma Software’s Adapters Help

November 16, 2026

What Is Dead Reckoning and How Simma Software’s Adapters Help

Drive into a long tunnel, and your phone’s blue dot usually freezes or wanders off. Underground, there is no open sky for GPS to listen to. The navigation system has to fall back on what it already knows: where the vehicle was a moment ago, how fast it’s moving, and which way it’s pointing. From those, it can make a sensible guess about where the vehicle is now. That guess is dead reckoning.

If you’re building vehicle tracking or navigation software, the movement data has to come from somewhere. Often that somewhere is the vehicle’s own network, and you need hardware that can read it. That’s where vehicle network adapters come in.

Simma Software makes these adapters for automotive and heavy-duty vehicles. They speak a number of common vehicle protocols and can plug into a host system in a few different ways. Below, we look at how dead reckoning works, why anyone bothers with it, and what part the adapters play.

What Is Dead Reckoning?

Dead reckoning means estimating your current position by starting from a known one and adding up how far and in which direction you’ve moved since. Sailors did this long before satellites existed, using speed, heading and time.

Modern systems use the same idea with different inputs: vehicle speed, heading, elapsed time, wheel movement, or readings from inertial sensors.

Back to the tunnel. Just before the vehicle goes in, the system has a good fix. Once the satellite signal drops, it keeps estimating progress from movement data until the signal comes back. How good that estimate is depends on two things: the quality of the measurements, and how long the outage lasts.

Why Is Dead Reckoning Used?

It’s useful whenever a system has to keep track of movement without a steady, reliable position fix from outside. Typical uses include:

  • Vehicle navigation during short GPS dropouts
  • Fleet monitoring and vehicle tracking
  • Automotive research and development
  • Commercial vehicle monitoring
  • Robotics and autonomous platforms
  • Navigation systems that blend several positioning sources

Think of it as a backup that earns its keep alongside other positioning methods. On its own, it isn’t meant to replace them.

How Does Dead Reckoning Work?

The system keeps updating its position estimate as new movement data arrives. The exact math depends on the sensors, the software and the overall design, but the process generally follows four steps.

  1. Establish an Initial Position

    Everything starts from a known position, usually supplied by a GPS receiver or another positioning source. This matters more than it sounds. If the starting point is off, every estimate after it inherits that error.

  2. Collect Movement Measurements

    Next, the system gathers data about how the vehicle is moving. The inputs might be wheel sensors, an inertial measurement unit, data from the vehicle network, or a mix. Whatever the source, the data has to suit the calculation it feeds.

  3. Calculate Position Changes

    The navigation software turns those measurements into distance and direction travelled. If a vehicle covers a measured distance on a known heading, the new position is easy to work out. Real driving is messier, of course. Turns and changes in speed all have to be factored in.

  4. Correct the Estimate When Possible

    Once a real position fix is available again, the system compares it with its own estimate and adjusts. Mixing independent sources like this is what keeps small errors from piling up into big ones.

What Role Does Vehicle Data Play in Dead Reckoning?

Vehicles produce a lot of data, and some of it describes movement. How useful it is comes down to what a particular vehicle actually exposes and how your application uses it.

Vehicle Speed and Movement Information

On vehicles that support it, network data can give an application speed or other movement-related readings, and those can feed navigation calculations if they’re suitable. Don’t assume they will be, though. Which signals exist, how often they update and how accurate they are all vary from one vehicle and network setup to the next.

Communication Between the Vehicle and Software

The adapter is the go-between. On one side is the vehicle’s network. On the other is your host system, whether that’s a laptop or an embedded computer. That lets software exchange data with the vehicle.

In a dead reckoning project, this link may be how vehicle data reaches the positioning software. Keep in mind that the adapter is the connection, not the calculator. Unless a specific model is documented as doing positioning work, assume the navigation math happens elsewhere.

How Simma Software’s Adapters Help

Simma Software’s adapters connect host systems to vehicle communication networks. The VNA family supports SAE J1939, SAE J1587, SAE J1708, OBD, ISO 15765 and CAN, depending on the product and configuration.

Connection options also vary by model. The range includes USB, serial and wireless interfaces.

Connecting Vehicle Networks to Host Devices

With a suitable adapter, a host device can talk to the vehicle networks it supports. Developers use that link to build diagnostic tools, monitoring systems, data loggers and other vehicle applications.

So the real question for any dead reckoning project is this: between them, can the adapter and the vehicle hand your navigation software the data it needs?

Supporting Compatible Dead Reckoning Configurations

Simma Software’s adapters support dead reckoning in compatible configurations. To pick the right model, check that model’s capabilities against what your system requires.

Before you choose, confirm that:

  • The adapter supports the vehicle’s communication protocol.
  • The vehicle actually provides the signals you need.
  • Your host system works with the adapter’s connection type.
  • Your application can read and process the incoming data.
  • Any extra positioning receivers, sensors or components are compatible.

Why so many checks? Because dead reckoning is a system-level job. The result depends on the hardware, the data sources, the software and the positioning method working together.

Supporting Vehicle Monitoring and Diagnostics

Navigation isn’t the only use. Some teams use adapters to pull diagnostic information or to watch traffic on the vehicle’s network. The software on top is different, yet the connection needs look a lot alike. As always, the right adapter depends on your protocols, interfaces and data requirements.

GPS vs. Dead Reckoning

The two do different jobs, and they work well together.

GPS Positioning

GPS uses satellite signals to estimate location, and when reception is good it gives dependable absolute positions. Tunnels, underground facilities and places where buildings or other structures block the sky are where it struggles.

Dead Reckoning Position Estimates

Dead reckoning builds on a previous position using movement measurements. It keeps producing estimates through short signal outages. The catch is drift: measurement errors add up over time, so the longer it runs without a correction, the less you can trust it.

Combining Both Methods

Put them together and each covers the other’s weakness. GPS sets or corrects the position, and dead reckoning fills the gaps when the signal disappears. How much better the result is depends on the implementation, the sensors, the calibration and the quality of the position data.

Where Is Dead Reckoning Used?

Automotive Navigation

Navigation systems use dead reckoning to keep estimating position where satellite reception is poor. Paired with other positioning sources, it helps keep a route from breaking up.

Fleet Management

Fleet software tracks journeys and vehicle locations. When tracking equipment supports it, dead reckoning can add supplementary estimates during brief interruptions.

Heavy-Duty Vehicles

Heavy trucks and other commercial vehicles run on electronic networks that carry both communication and diagnostic traffic. On a compatible system, some of that data can be passed to monitoring or navigation software.

Robotics and Autonomous Platforms

Robots can work out how far they’ve moved from their own onboard measurements. The trouble is that small errors stack up when that’s all they have, so dead reckoning is usually paired with other localization methods.

Benefits and Limitations of Dead Reckoning

Benefits

Its main strength is keeping a position estimate alive when outside signals drop out. It also combines well with other sensors and positioning technologies, so it can be tuned to different operating needs. How much value you get depends on the quality and availability of the movement data.

Limitations

It won’t give you an exact position. Small measurement errors accumulate, and the estimate slowly drifts from where the vehicle really is.

A few more things to plan for. Not every vehicle exposes the data you want, sensors need calibrating, and you’ll need software capable of handling all of it. An adapter on its own won’t supply every piece of hardware and software a full navigation solution needs.

How to Choose a Simma Software Adapter

Identify the Required Protocols

Start by listing the vehicle communication protocols your application needs. Then check that the adapter supports them and works with your intended vehicle setup.

Select a Suitable Interface

Decide whether your host system needs USB, serial or wireless. Confirm compatibility with the host device and your application before you install anything.

Verify Data Availability

Work out exactly which vehicle signals your application needs. Then check that the vehicle network carries them and that the adapter and your software can reach them.

Confirm Dead Reckoning Requirements

Look up the dead reckoning support for the model you’re considering, and find out whether you’ll need extra sensors, positioning equipment or software.

Consider the Complete System

Look at the vehicle, adapter, host device, sensors and application as one design. A system that fits together well matters more than an adapter that simply looks good on an interface or protocol list.

Frequently Asked Questions

It’s estimating where you are now from where you were before, plus information about how you’ve moved, such as speed and direction.

Yes. A suitable system can keep estimating movement without a continuous GPS signal, as long as it gets the measurements it needs. Errors will build up, though, until a real fix lets the system correct itself.

They connect vehicle networks to host systems. If the vehicle supplies the right measurements and your application supports them, that connection can pass vehicle data to the positioning system.

They do, in compatible configurations. Check the exact capabilities and any additional requirements for your adapter model and application.

The VNA family is built for vehicle network connectivity and supports several protocols used in both heavy-duty and light-duty vehicles. Check the specifications of the exact model before you commit to it for a project.

Not by itself. A complete solution may also need sensors, positioning equipment, navigation software and some integration work.

Conclusion

Dead reckoning lets a system keep estimating vehicle movement when continuous external positioning isn’t available. It helps navigation stay smooth, but the estimate is only as good as the measurements, the software and the overall design.

Simma Software’s vehicle network adapters can play a part in compatible dead reckoning setups by linking host systems to supported vehicle networks. Picking the right model means confirming protocol support, available vehicle data, connection requirements and any extra positioning components.

For product-specific details, consult the Simma Software adapters page and the official adapter FAQ.